What is a screen and recoat on hardwood floors?
Your hardwood has a clear protective finish on top of the wood. Everyday traffic wears and scratches that finish long before it reaches the wood itself. A screen and recoat works only on that top layer.
First we buff the whole floor with a fine abrasive screen. That takes off the light scratches and dulls the old finish so the new coat can grip it. Then we vacuum and tack the floor clean and roll on a fresh coat of finish. The wood is never sanded down, so the color stays the same and the floor keeps its thickness.
Screen and recoat vs full sand and refinish: which do you need?
A quick way to tell: look at your worst scratches.
- Gray or white scratches that sit on the surface are in the finish. A screen and recoat can usually take care of those.
- Scratches that show bare, darker or lighter wood, worn-through traffic lanes, deep gouges, pet nail damage into the wood, water stains or boards that have turned black mean the finish is already gone in those spots. That floor needs a full sand and refinish, which we’ll tell you up front instead of selling you a recoat that won’t fix it.
If you want a new stain color, that also takes a full sand, since stain has to go on bare wood.
Can every hardwood floor be recoated?
Not every one, and this is where a recoat goes wrong when it’s rushed. New finish has to bond to the old finish. Three things can stop that:
- Wax. Floors that were ever waxed, or cleaned with products that leave a wax or polish film, won’t let new finish stick.
- Some factory finishes. Many prefinished floors have a very hard factory coating that needs a different prep before a recoat will hold.
- Heavy residue. Years of oil soap or shine products leave a film that has to come off first.
So we test before we commit. If your floor isn’t a good candidate, we’ll tell you, and you won’t pay for a coat that peels.
How long before you can walk on a recoated floor?
It depends on the finish and the weather, but for most jobs:
- Socks only: the next day.
- Furniture back: after about 2 days. Lift it, don’t slide it, and put felt pads on the legs.
- Area rugs back: after about a week, while the finish finishes hardening underneath.
Knoxville humidity slows drying in the summer, so we’ll give you the times for your floor and your finish before we start. Plan to keep pets off the floor until it can take shoes.
How often should hardwood floors be recoated?
There’s no fixed calendar. A busy kitchen, entry or hallway with dogs wears through its finish much faster than a formal dining room. The best time to recoat is when the floor first starts to look dull and scratched in the traffic lanes, before those lanes wear through to bare wood. Recoat in time and you may never need a full sand. Wait too long and you will.
How do you get your hardwood ready for a recoat?
- Clear the room of furniture, rugs and anything on the floor. If you need a hand with heavy pieces, ask when you book.
- Stop using any shine, polish or oil soap products now. Tell us what you’ve used in the past; it matters for the bond.
- Plan where people and pets will go while the floor dries, and which door we’ll use.
- Turn the HVAC to a normal setting. Very hot, cold or humid rooms change drying times.
How should you clean hardwood after a recoat?
Keep it simple. Dry dust mop or vacuum on the hard-floor setting, and damp mop with a cleaner made for finished wood floors, wrung out until it’s barely damp. Skip steam mops, wax, oil soaps and “shine restorers”; they either damage the finish or leave a film that blocks the next recoat. Put mats at the doors and felt pads under furniture, and your new coat will last a lot longer.
Do you also clean the rugs and carpet that go back on the floor?
Yes, and it’s a good time to do it. Rugs come off the floor for the recoat anyway, so we can clean them on site or pick them up, clean them and bring them back once the floor is ready. See area rug cleaning. If you have carpet in the next rooms, we can do carpet cleaning on the same visit.