(865) 255-9692Open 24/7: call or text
Get a quote

LVP and VCT floor cleaning in Knoxville, TN

Vinyl floors are tough, but the textured surface and the seams trap dirt a mop just pushes around. A proper scrub and rinse gets the floor back to its real color without the film that makes it look dull again a week later.

Quick answer

We machine scrub luxury vinyl plank and VCT with a pH-neutral cleaner, rinse the residue off and dry the floor as we go, with no steam heat or standing water. Most floors are dry and ready to walk on within about 1 hour.

Call or text 24/7(865) 255-9692

(865) 255-9692

CallText
Ask Walt

Why does LVP still look dirty after you mop it?

Most luxury vinyl plank has a textured, wood-grain surface. Dirt settles into that texture and into the bevels between planks, and a mop glides right over it. Many store-bought floor cleaners and “shine” products also leave a thin film behind. That film grabs new dirt, so the floor looks dull and gray faster each time, and footprints show up on it.

A machine scrub reaches into the texture and the seams, and a rinse takes the cleaner back off the floor so there’s nothing left to grab dirt.

Can you steam clean luxury vinyl plank?

We don’t, and we’d steer you away from steam mops on it too. Heat and steam can soften the adhesive, lift edges and get water into the seams, and some plank makers warn against it. Vinyl doesn’t need heat to come clean. It needs the right cleaner, agitation and a rinse, with as little water left on the floor as possible.

Why do the seams on vinyl plank floors turn black?

The small bevel where two planks meet is a groove, and every mop pass pushes a little dirty water into it. Over time the dirt dries in that groove in a dark line, and the floor looks grimy even right after you mop. A brush on a floor machine reaches down into the bevels and lifts that soil out, and a rinse carries it away instead of leaving it in the next groove over. It’s often the single biggest difference people notice after we clean an LVP floor.

How do you clean LVP and VCT floors?

  • Dry soil first. We vacuum the floor so grit doesn’t get dragged across it.
  • pH-neutral cleaner. Harsh, high-pH degreasers can dull the wear layer. We use a neutral cleaner made for resilient floors.
  • Machine scrub. A floor machine with soft brushes or pads works the cleaner into the texture and the seams.
  • Rinse and pick up. We rinse and pull the dirty water back up instead of letting it sit.
  • Edges by hand. Corners, baseboard lines and around cabinets get detailed by hand.

What is VCT, and is it cleaned the same way?

VCT is vinyl composition tile, the square tile you see in schools, stores, offices, break rooms and a lot of basements and laundry rooms. Unlike LVP, VCT is usually protected with coats of floor finish, the “wax” that gives it a shine.

For VCT we can scrub the floor and put down fresh coats of finish to bring back the shine, or, when the old finish is yellowed, scratched and built up, strip it to bare tile and lay down new coats. We’ll tell you which your floor needs after we look at it.

Should luxury vinyl plank be waxed or polished?

Usually not. Most LVP has a factory wear layer that isn’t meant to take wax, and polish products build up into a cloudy, sticky film that’s hard to get off. If your plank looks hazy or streaky, there’s a good chance it’s product buildup, not wear. Our scrub and rinse often takes that buildup off and the floor looks better than it has in years.

Do you clean vinyl floors in rentals and businesses?

Yes. LVP and VCT are everywhere in rentals, offices and shops because they hold up. We clean them for move-outs and make-readies, and on a schedule for businesses. See janitorial and make-readies and commercial carpet cleaning if you have carpet too.

How do you keep vinyl floors clean between visits?

  • Sweep or vacuum (hard-floor setting, no beater bar) a few times a week. Grit is what scratches the wear layer.
  • Damp mop with a pH-neutral cleaner, wrung out well. Skip vinegar-heavy mixes, bleach and “mop and shine” products.
  • Put mats at the doors and felt pads under chairs.
  • Wipe spills up quickly so liquid doesn’t sit in the seams.

How a vinyl floor cleaning visit goes

  1. 1

    Look

    We check the floor type, the seams and any buildup or damage, and quote on site.

  2. 2

    Vacuum

    We take the loose grit off so it doesn’t scratch the floor while we scrub.

  3. 3

    Scrub

    We machine scrub with a pH-neutral cleaner made for resilient floors.

  4. 4

    Rinse and dry

    We rinse, pick the water back up and detail the edges by hand.

  5. 5

    Finish VCT

    On VCT, we put down fresh coats of floor finish if the floor calls for it.

Common questions

How long until I can walk on the floor?

Most cleaned LVP is dry within about 1 hour. VCT with fresh finish needs longer, usually a few hours before shoes and overnight before heavy carts or furniture.

Can you get rid of the haze on my vinyl plank?

Often, yes. Haze is usually built-up cleaner or polish, not damage. A scrub and rinse takes most of it off. Scratches in the wear layer won’t clean out.

Do you clean laminate floors?

Laminate has a wood-fiber core that swells with water, so it needs even less moisture than vinyl. Ask us about your floor and we’ll tell you what’s safe for it.

Do you clean the grout on tile floors too?

Yes. Ceramic and porcelain tile with grout lines is its own service. See tile and grout cleaning.

Are your cleaners safe for kids and pets?

Yes. We use green, eco-friendly cleaning solutions that are safe for pets and kids once the floor is dry.

How much does LVP or VCT cleaning cost?

We quote on site, since it depends on the size of the floor and whether VCT needs new finish. You get the price before we start. See our pricing page for our other services.

What customers say on Google

4.5 out of 5 from 33 Google reviews. Read our reviews.

Page updated